ISO STANDARS FOR PAINT AND VARNISH

ISO 4618:2006 Paints and varnishes – Terms and definitions.

ISO 8501-1:2007 Preparation of steel substrates before application of paints and related products – Visual assessment of surface cleanliness – Part 1: Rust grades and preparation grades of uncoated steel substrates and
of steel substrates after overall removal of previous coatings.

ISO 8501-2:1994 Preparation of steel substrates before application of paints and related products – Visual assessment of surface cleanliness – Part 2: Preparation grades of previously coated steel substrates after localized
removal of previous coatings

ISO 8501-3:2006 Preparation of steel substrates before application of paints and related products – Visual assessment of surface cleanliness – Part 3: Preparation grades of welds, edges and other areas with surface
imperfections.

ISO 8501-4:2006 Preparation of steel substrates before application of paints and related products – Visual assessment of surface cleanliness – Part 4: Initial surface conditions, preparation grades and flash rust grades in connection with high-pressure water jetting.

ISO 8502-2:2005 Preparation of steel substrates before application of paints and related products – Tests for the assessment of surface cleanliness – Part 2: Laboratory determination of chloride on cleaned surfaces

ISO 8502-3:1992 Preparation of steel substrates before application of paints and related products – Tests for the
assessment of surface cleanliness – Part 3: Assessment of dust on steel surfaces prepared
for painting (pressure-sensitive tape method)

ISO 8502-4:1993 Preparation of steel substrates before application of paints and related products – Tests for the
assessment of surface cleanliness – Part 4: Guidance on the estimation of the probability of condensation prior to paint application.

ISO 8502-5:1998 Preparation of steel substrates before application of paints and related products – Tests for the
assessment of surface cleanliness – Part 5: Measurement of chloride on steel surfaces Prepared for painting (ion detection tube method).

ISO 8502-6:2006 Preparation of steel substrates before application of paints and related products – Tests for the
assessment of surface cleanliness – Part 6: Extraction of soluble contaminants for analysis – The Bresle method.

ISO 8502-8:2001 Preparation of steel substrates before application of paints and related products – Tests for the
assessment of surface cleanliness – Part 8: Field method for the refractometric determination of moisture.

ISO 8502-9:1998 Preparation of steel substrates before application of paints and related products – Tests for the
assessment of surface cleanliness – Part 9: Field method for the conductometric determination of
water-soluble salts.

ISO 8502-11:2006 Preparation of steel substrates before application of paints and related products – Tests for the
assessment of surface cleanliness – Part 11: Field method for the turbidimetric determination of water-soluble sulfate.

ISO 8502-12:2003 Preparation of steel substrates before application of paints and related products – Tests for the
assessment of surface cleanliness – Part 12: Field method for the titrimetric determination of water-soluble ferrous ions.

ISO 8503-1:2012 Preparation of steel substrates before application of paints and related products – Surface roughness characteristics of blast-cleaned steel substrates – Part 1: Specifications and definitions for ISO surface
profile comparators for the assessment of abrasive blast-cleaned surfaces.

ISO 8503-2:2012 Preparation of steel substrates before application of paints and related products – Surface roughness characteristics of blast-cleaned steel substrates – Part 2: Method for the grading of surface profile of
abrasive blast-cleaned steel – Comparator procedure.

ISO 8503-3:2012 Preparation of steel substrates before application of paints and related products – Surface roughness characteristics of blast-cleaned steel substrates – Part 3: Method for the calibration of ISO surface
profile comparators and for the determination of surface profile – Focusing microscope procedure.

ISO 8503-4:2012 Preparation of steel substrates before application of paints and related products – Surface roughness characteristics of blast-cleaned steel substrates – Part 4: Method for the calibration of ISO surface
profile comparators and for the determination of surface – Stylus instrument procedure.

ISO 8503-5:2003 Preparation of steel substrates before application of paints and related products – Surface roughness characteristics of blast-cleaned steel substrates – Part 5: Replica tape method for the determination
of the surface profile.

ISO 8504-1:2000 Preparation of steel substrates before application of paints and related products – Surface preparation methods – Part 1: General principles.

ISO 8504-2:2000 Preparation of steel substrates before application of paints and related products – Surface preparation methods – Part 2: Abrasive blast-cleaning.

ISO 8504-3:1993 Preparation of steel substrates before application of paints and related products – Surface preparation methods – Part 3: Hand- and power-tool cleaning.

ISO 11124-1:1993 Preparation of steel substrates before application of paints and related products – Specifications for metallic blast-cleaning abrasives – Part 1: General introduction and classification.

ISO 11124-2:1993 Preparation of steel substrates before application of paints and related products – Specifications for metallic blast-cleaning abrasives – Part 2: Chilled-iron grit.

ISO 11124-3:1993 Preparation of steel substrates before application of paints and related products – Specifications for metallic blast-cleaning abrasives – Part 3: High-carbon cast-steel shot and grit.

ISO 11124-4:1993 Preparation of steel substrates before application of paints and related products – Specifications for metallic blast-cleaning abrasives – Part 4: Low-carbon cast-steel shot.

ISO 11125-1:1993 Preparation of steel substrates before application of paints and related products – Test methods for metallic blast-cleaning abrasives – Part 1: Sampling.

ISO 11125-2:1993 Preparation of steel substrates before application of paints and related products – Test methods for metallic blast-cleaning abrasives – Part 2: Determination of particle size distribution.

ISO 11125-3:1993 Preparation of steel substrates before application of paints and related products – Test methods for metallic blast-cleaning abrasives – Part 3: Determination of hardness.

ISO 11125-4:1993 Preparation of steel substrates before application of paints and related products – Test methods for metallic blast-cleaning abrasives – Part 4: Determination of apparent density.

ISO 11125-5:1993 Preparation of steel substrates before application of paints and related products – Test methods for metallic blast-cleaning abrasives – Part 5: Determination of percentage defective particles and of microstructure.

ISO 11125-6:1993 Preparation of steel substrates before application of paints and related products – Test methods for metallic blast-cleaning abrasives – Part 6: Determination of foreign matter.

ISO 11125-7:1993 Preparation of steel substrates before application of paints and related products – Test methods for metallic blast-cleaning abrasives – Part 7: Determination of moisture.

ISO 11126-1:1993 Preparation of steel substrates before application of paints and related products – Specifications for non-metallic blast-cleaning abrasives – Part 1: General introduction and classification.

ISO 11126-1:1993 Preparation of steel substrates before application /Cor 1:1997 of paints and related products – Specifications for non-metallic blast-cleaning abrasives – Part 1: General introduction and classification.

ISO 11126-1:1993 Preparation of steel substrates before application /Cor 2:1997 of paints and related products – Specifications for non-metallic blast-cleaning abrasives – Part 1: General introduction and classification.

ISO 11126-3:1993 Preparation of steel substrates before application of paints and related products – Specifications for non-metallic blast-cleaning abrasives – Part 3: Copper refinery slag.

ISO 11126-4:1993 Preparation of steel substrates before application of paints and related products – Specifications for non-metallic blast-cleaning abrasives – Part 4: Coal furnace slag.

ISO 11126-5:1993 Preparation of steel substrates before application of paints and related products – Specifications for non-metallic blast-cleaning abrasives – Part 5: Nickel refinery slag.

ISO 11126-6:1993 Preparation of steel substrates before application of paints and related products – Specifications for non-metallic blast-cleaning abrasives – Part 6: Iron furnace slag.

ISO 11126-7:1995 Preparation of steel substrates before application of paints and related products – Specifications for non-metallic blast-cleaning abrasives – Part 7: Fused aluminium oxide.

ISO 11126-7:1995 Preparation of steel substrates before application/Cor 1:1999 of paints and related products – Specifications for non-metallic blast-cleaning abrasives – Part 7: Fused aluminium oxide.

ISO 11126-8:1993 Preparation of steel substrates before application of paints and related products – Specifications for non-metallic blast-cleaning abrasives – Part 8: Olivine sand.

ISO 11126-9:1999 Preparation of steel substrates before application of paints and related products – Specifications for non-metallic blast-cleaning abrasives – Part 9: Staurolite.

ISO 11126-10:2000 Preparation of steel substrates before application of paints and related products – Specifications for non-metallic blast-cleaning abrasives – Part 10: Almandite garnet.

ISO 11127-1:2011 Preparation of steel substrates before application of paints and related products – Test methods for non-metallic blast-cleaning abrasives – Part 1: Sampling.

ISO 11127-2:2011 Preparation of steel substrates before application of paints and related products – Test methods for non-metallic blast-cleaning abrasives – Part 2: Determination of particle size distribution.

ISO 11127-3:2011 Preparation of steel substrates before application of paints and related products – Test methods for non-metallic blast-cleaning abrasives – Part 3: Determination of apparent density.

ISO 11127-4:2011 Preparation of steel substrates before application of paints and related products – Test methods for non-metallic blast-cleaning abrasives – Part 4: Assessment of hardness by a glass slide test.

ISO 11127-5:2011 Preparation of steel substrates before application of paints and related products – Test methods for non-metallic blast-cleaning abrasives – Part 5: Determination of moisture.

ISO 11127-6:2011 Preparation of steel substrates before application of paints and related products – Test methods for non-metallic blast-cleaning abrasives – Part 6: Determination of water-soluble contaminants by
conductivity measurement.

ISO 11127-7:2011 Preparation of steel substrates before application of paints and related products – Test methods for non-metallic blast-cleaning abrasives – Part 7: Determination of water-soluble chlorides.

ISO 12944-1:1998 Paints and varnishes – Corrosion protection of steel structures by protective paint systems
– Part 1: General introduction.

ISO 12944-2:1998 Paints and varnishes – Corrosion protection of steel structures by protective paint systems
– Part 2: Classification of environments.

ISO 12944-3:1998 Paints and varnishes – Corrosion protection of steel structures by protective paint systems
– Part 3: Design considerations.

ISO 12944-4:1998 Paints and varnishes – Corrosion protection of steel structures by protective paint systems
– Part 4: Types of surfaces and surface preparation.

ISO 12944-5:2007 Paints and varnishes – Corrosion protection of steel structures by protective paint systems
– Part 5: Protective paint systems.

ISO 12944-6:1998 Paints and varnishes – Corrosion protection of steel structures by protective paint systems
– Part 6: Laboratory performance test methods.

ISO 12944-7:1998 Paints and varnishes – Corrosion protection of steel structures by protective paint systems
– Part 7: Execution and supervision of paint work.

ISO 12944-8:1998 Paints and varnishes – Corrosion protection of steel structures by protective paint systems
– Part 8: Development of specifications for new work and maintenance.

ISO/TR 15235:2001 Preparation of steel substrates before application of paints and related products – Collected
information on the effect of levels of water-soluble salt contamination.

ISO 15741:2001 Paints and varnishes – Friction-reduction coatings for the interior of on- and offshore steel pipelines
for non-corrosive gases.

ISO 16276-1:2007 Corrosion protection of steel structures by protective paint systems – Assessment of, and acceptance criteria for, the adhesion/cohesion (fracturestrength) of a coating – Part 1: Pull-off testing.

ISO 16276-2:2007 Corrosion protection of steel structures by protective paint systems – Assessment of, and
acceptance criteria for, the adhesion/cohesion (fracturestrength) of a coating – Part 2: Cross-cut testing and X-cut testing.

ISO 19840:2004 Paints and varnishes – Corrosion protection of steel structures by protective paint systems
– Measurement of, and acceptance criteria for, the thickness of dry film on rough surfaces.

ISO 20340:2009 Paints and varnishes – Performance requirements for protective paint systems for offshore and
related structures.

ISO 29601:2011 Paints and varnishes – Corrosion protection by protective paint systems – Assessment of porosity
in a dry film.